If your air tools struggle to live out their warranty or require more maintenance than the manufacturer’s guidelines state, there’s a good chance you are using too much air pressure.
Many air compressor operators over-pressurize their pneumatic tools as a standard operating procedure. The assumption is you get more power out of a tool if you apply more pressure. While this is true sometimes, it isn’t always true, and it leads to premature tool wear, breakage or worse...
In this article, we've list the reasons you should always use the proper pressure for your air tools:
Too much pressure can cause your air tools to wear out or break sooner than they should. A few of the most common pneumatic tool repairs caused by excessive air pressure include:
Blown seals: The more pressure you use, the bigger the opportunity for blown seals. You might as well use your shop vac to suck the extra cash out of your pockets if you don’t protect yourself from blown seals because they result in expensive repair bills.
Anvil breakage: Anvil breakage is far too common. Operators apply more pressure to their impact wrenches to get more torque. Then the anvil cracks or breaks, which means you’ve wasted any time saved due to extra torque and have a new bill for repair costs.
Bearing failure: Besides blown seals and anvil breakage, using too much pressure is one of the most direct causes of bearing failure. If you’ve worked with air tools for a while, you know bearing failure is expensive, and you probably also know that if the bearings go, you already have many more damaged parts to repair.
Motor breakdowns: As little as 20 psi of excessive pressure in a motor system can half the life of an air tool. Most tools are rated at 90 or 100 psi, so using 120 psi regularly ensures you will replace expensive air tools in half the time you should have to.
In many cases, a broken tool doesn’t happen in an instant. Instead, tools wear down over time until they reach a point of failure. The more a tool is worn down, the less efficient seals and other components become, even if it’s still working. This results in leaked air, which means the tool needs even more air to run than it usually would.
Using the right pressure for your tools reduces wear and improves tool efficiency. If you care about getting the best performance from your tools, stop using too much pressure.
Tools that break or fail and can’t be repaired will need to be replaced, and we don’t need to tell you that new tool costs add up quickly! It’s an unnecessary expense that could have been reinvested elsewhere.
Consider this: when you buy an air tool from a manufacturer or dealer, they give you a price, and you either agree to pay the price or negotiate a discount. You never ask them to take more money from you. Yet, if you don’t properly care for your air tools, you might as well do that.
Treat your tools with respect and save your money for better purchases.
Let’s put the financial impacts aside because you won’t be thinking about expenses when you or one of your employees suffers a devastating or fatal injury. It’s easy to shrug off safety regulations and assume a severe injury would never happen to you or your team. However, pressure safety warnings exist in manufacturers’ guidelines for a reason.
We’ve heard stories about tool technicians killed when an over-pressured grinder explodes because it’s operating at speeds much higher than the manufacturer’s safety ratings. You don’t want your team to be the one that proves these urban legends are true.
But even if the stories are false, the pneumatic tool manufacturers are concerned enough to include pressure rating warnings in their manuals. For example, here’s what Central Pneumatic says in their ¼” angle die grinder manual:
“Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range.”
Protect your team and your business by keeping everyone safe. Follow the pressure guidelines and you can prevent serious consequences.
Last but possibly not least, using the proper pressure will lower your fuel consumption and air compressor emissions.
Pressure (psi) and volume (CFM) have an inverse relationship. Therefore, if available energy (horsepower) is fixed, the higher the pressure required, the lower the volume of air that is available. If both higher pressure and volume are required, more energy will be necessary.
In either case, if a tool requires more pressure or volume to operate, you spend extra energy on wasted air—meanwhile, higher horsepower results in higher fuel consumption, which increases operating costs.
Manufacturing engineers create and test tools using the same psi ranges published in the tools’ manuals. If your tool isn’t performing as well as you think it should, the pressure rating isn’t the problem. Instead of cranking up the pressure, take the following steps:
One last tip—don’t use sound when determining if a tool is working. We’ve met operators who think their tool or air compressor is too weak because their tools get quieter after the air has run for a few seconds, even when the tools are operating just fine! Instead of listening, look at how the tool is performing to determine whether it gets the job done in a normal amount of time.
At the end of the day, too much pressure for your air tools can be a costly mistake. From equipment failure and repair costs to health and safety risks for your team, there are a lot of reasons you should simply use the right pressure.
It’s unlikely all the terrible things in this article will happen to your team and equipment if you use too much pressure. However, it’s probable you’ll encounter at least some of the issues, including the frustration that goes along with them.
By contrast, eliminating the issues caused by too much pressure is easy to do. Use the proper pressure for your air tools and rest assured you’re getting the most out of your tools.